Practical Implementation of Lead-Free Soldering The Experience of the Japanese Electronics Industry

With the US military now committed to the phasing
out of lead-containing solders via the Joint Group on
Pollution Prevention (JG-PP) the electronics industry
has moved beyond debate about whether to make this
move and onto the question of how to implement the
change to lead-free solders as quickly as possible
without increasing cost or reducing reliability. The
Japanese industry began this change several years
ago and already has a vast amount of experience in
practical lead-free soldering and the resolution of the
technical issues that were inevitably encountered.
Although,because of the impact of legislative
pressure lead-free solders were initially used mainly
in consumer electronics the commitment of the
industry to environmental protection has meant that
these solders are now being introduced across a wide
spectrum of electronics. In this paper some of the
technical challenges encountered in the
implementation of lead-free solder will be discussed
and the solutions reported. The conclusion is that the
electronics industry can meet the challenges
presented by the phas ing out of lead-free solders in
much the same way as it deal with earlier challenges
such as the phasing out of CFC cleaning solvents and
the introduction of surface mount technology.

Author(s)
Tetsuro Nishimura,Keith Sweatman
Resource Type
Technical Paper
Event
IPC APEX 2003

2D Off-line X-ray Inspection in the SMT Production Line: Working Towards the Zero-Defect Goal

The goal of SMT production is a zero-defect process in which flawed materials never get to the customer; however,
in the ideal scenario,zero-defect production would mean that no flawed products ever come off the production line.
The typical SMT production line,which integrates inspection as a defect-containment method,operates with less
efficiency and effectiveness than is possible with modern technology,making the zero-defect proposition difficult to
achieve. The effort to increase product quality with inspection stations integrated into the product line can have two
results: no appreciable increase in quality metrics; and/or a loss of production line efficiency due to bottlenecks,
caused by choosing the wrong inspection system. In order to achieve increased quality,product yield,and line
efficiency,one must employ the right inspection system in the right way for process development and improvement,
not just defect containment.
What is the right system? Electronics packages are becoming increasingly smaller and more densely populated.
With this comes the need for high-intensity,nondestructive inspection that is both thorough and fast. X-ray
inspection is the only method of nondestructive testing that can provide high-level detection of the most-common
production defects: solder short,solder open,insufficient solder and reliability,and missing parts. Furthermore,only
offline X-ray inspection systems have the speed,imaging capabilities,and flexibility to create a zero-defect process.
What is “the right way?” In order to make quality a value-added part of the process at every level,the design of the
production line must reflect this goal. Inspection is not merely for post-production. A closed-loop production
process sets goals to achieve quality at all stages: setting process limits,measuring the process,controlling the
process,decreasing defect rate,and increasing first-pass yield.
This paper will analyze the typical SMT production process in terms of line setup,the role of inspection,the level of
quality achieved,and flaws in the process. We will also suggest an “ideal” SMT production line with regard to line
setup,the right inspection system to meet those goals,and the anticipated benefits towards achieving a zero-defect
result.

Author(s)
Jon Dupree
Resource Type
Technical Paper
Event
IPC APEX 2003

Biologically Inspired Vision Makes for Smarter PCBA Manufacturing Technology - New Technologies Overcome Fundamental Limitations of Conventional Optical Inspection Methods

For test engineers and managers,automated optical
inspection (AOI) systems have emerged as a
countermeasure to the growing threats of lost
physical or electrical access to assembled PCB. AOI
systems are successfully employed in high volume
PCB applications to complement existing electrical
test methods with noted results of overall better
coverage,and higher yield at later test stages.
Inspection systems are commoditized,readily
available from many suppliers,and primarily
evaluate the presence of assembly defects (solder,
component,assembly),overcoming the need for
physical access that test mandates.

Author(s)
John Arena,Pamela Lipson
Resource Type
Technical Paper
Event
IPC APEX 2003

Increased Productivity in X-ray Inspection – The Role of ADR Technology

The economic environment in the electronics
industry has changed dramatically over the last two
years. The focus on the production floor has moved
from increasing capacity to improving the yield. One
of the major consequences of this shift in focus has
been increased interest in x-ray inspection.

Author(s)
Vikram Butani
Resource Type
Technical Paper
Event
IPC APEX 2003

Manufacturing Process Management – Facilitating Stage 3 of Manufacturing Outsourcing

The slowdown in the electronics industry has allowed the management of electronics products manufacturers to
dedicate time to reconsider their manufacturing strategy. For most of these companies,outsourcing has been in its
interim stages of giving it a try (stage 1) or outsourcing most of its PCB assemblies and/or selling off facilities (stage
2).
Original Equipment Manufacturers (OEMs) should be looking for ways to enter stage 3 of outsourcing - reconsider
the manufacturing strategy,outsource the final assembly (box build) along with PCB assembly and minimize
management costs.
While more and more companies are now looking to further reduce costs and to more quickly introduce new
products to the market,they are also concerned with losing core manufacturing knowledge as well as visibility to,
and control of,the outsourced job.

Author(s)
Sharron Lifshitz
Resource Type
Technical Paper
Event
IPC APEX 2003

Increasing Operating Margins in a Down Economy: Case Studies in SMT Production Monitoring Software & Applications

Shrinking profits and overcapacity have forced Electronics Manufacturers to squeeze every last penny out of Site
Operations. To reduce conversion costs in a short timeframe,some facilities have employed Motorola's
Manufacturing Pulse™ software to promote visibility and real-time control of materials on the shop floor. This
paper will discuss real-world case studies explaining the methodology and tools used to reduce scrap costs by as
much as 46%,while reducing the downtime incurred from material outages. Detailed methodologies include realtime
Statistical Process Control (SPC) on materials attrition,real-time performance alarming to technicians,
historical materials performance reporting,and ERP system integration. In addition,this paper describes how this
single tool covers multiple equipment types such as Fuji CP6,Siemens S20,Siemens F5,Siemens HS50,Universal
GSM2,Universal HSP,Panasonic MPA,and Panasonic MV2.

Author(s)
Dan Kauss
Resource Type
Technical Paper
Event
IPC APEX 2003

Management of DPMO Metrics Reduces the Cost of PCB Assembly

Manufacturers can use DPMO metrics to reduce the cost of PCB assembly with fewer resources. DPMO data can be
used for predicting the fault spectrum on future products,quoting new business,setting quality targets for
manufacturing,defining test strategies,predicting yields,or estimating shipped quality levels. Manufacturers can
input DPMO and BOM data into cost calculator tools to estimate manufacturing costs. When combined with a few
site-specific assumptions about labor rates and test strategy,roughly 80% of PCB assembly costs fall into place once
there is a clear definition of the DPMO. In this way,manufacturers can determine targets for both in-process quality
and financial profit and loss. Tools are now available to the industry that make use of DPMO data for strategic
decision making applications. Use case examples are shown.

Author(s)
Amit Verma
Resource Type
Technical Paper
Event
IPC APEX 2003

A Case Study of In-Process Inspection Methods to Improve First Pass Yields

The electronics content of many consumer products has increased substantially over the past decade. Several of the
electronics added to the automobile control vehicle functions that have a direct bearing on the well being and safety
of the passengers being transported. Automotive electronics are also subjected to very harsh environments. For these
reasons,the reliability and quality of electronics components is of utmost concern. Many products are built with a
“no touch-up rule” that prohibits rework if the product does not pass end of line test. For the electronics assembler
this places a heavy burden on a high first pass yield process. The purpose of this paper is to discuss and present
results from a test and inspection strategy adopted by an SMT assembler that includes in-line 3D solder paste and
component inspection to improve first pass yields.

Author(s)
Stacey Wagner,David Clark
Resource Type
Technical Paper
Event
IPC APEX 2003

Comparison of X-ray Inspection Systems for BGA/CCGA Quality Assurance and Crack Detection

For high reliability applications,the use of x-ray technique has become an additional inspection requirement for
quality control and detection of unique defects due to manufacturing of advanced electronic packages such as ball
grid array (BGAs) and chip scale packages (CSPs). Recently,four x-ray systems were evaluated for their defect
detection capability,especially for damage/cracks induced during thermal cycling of ceramic column grid array
(CCGA)/BGA assemblies. These systems were:
1. Case 1: A 2D real time x-ray with a microfocus source and image intensifier as detector. For this case,position
of detector to x-ray source is a straight line.
2. Case 2: A 2D system with x-ray transmission similar to the case 1 with the exception of detector had off-axis
rotational capability,therefore; providing oblique views at higher magnifications.
3. Case 3: A fully digital tomosynthesis x-ray system that is capable to combine 3D volumetric imaging and
conventional 2D x-ray for a complete inspection.
4. Case 4: A custom made 3D computed tomography (CT) x-ray system. It utilizes a high power microfocus
source (cone and parallel beam) and glass scintillator detector or flat panel digital detector to obtain crosssectional
2D x-ray images with preprogrammed angle views. The reconstruction algorithm then provides a true
3D volumetric display
This paper discusses limitation of each system and provides representative inspection images for CCGA/BGA
assemblies. The assemblies have subjected to various thermal cycle and ranges and have shown different levels of
damage/cracking. The x-ray images were compared to optical images taken by a 3D optical microscopy for outer
rows of array package assemblies.

Author(s)
R. Ghaffarian,D. Mih
Resource Type
Technical Paper
Event
IPC APEX 2003

Investigation of the Effectiveness of Automated X-ray Inspection Systems in a High Volume – Low Mix SMT Line

The advent of miniature surface mount components coupled with increasing lead counts has posed tremendous
challenges during assembly. This is especially true in an Electronics Manufacturing Service (EMS) industry where
the focus has been to increase throughput and first pass yields at lowest cost. Therefore,robust and repeatable
inspection systems need to be employed in order to achieve these objectives. Due to the constraints imposed by the
existing inspection technologies,the effectiveness of automated x-ray inspection system was investigated from a
statistical and assembly perspective. The results were analyzed and significant measures were initiated and
employed to improve the performance of the automated x-ray inspection system and subsequently of the Surface
Mount Technology (SMT) line.

Author(s)
Praveen Kumar Manjeshwar,Sachin Phadnis,K. Srihari,Jorge Craik
Resource Type
Technical Paper
Event
IPC APEX 2003